Tarmac Restorer BLACK
High Quality Repair Coating - Replaces Lost Resin & Colour, Easy to Apply. Transforms Old Tarmac
Black tarmac restorer for use on black tarmac Driveways, Car Parks, Playgrounds and Tennis Courts
Repair and restore tarmac driveways with Tarmaseal
Smartseal Tarmac sealer is a superb easy to apply Tarmac restorer designed to rejuvenate and transform tired black tarmac. Tarmaseal is far superior to a tarmac paint and offers a cost effective alternative to a full replacement of a driveway. For more detailed information visit our dedicated Tarmac Paint website.
- Transform the appearance of any existing Tarmac driveway
- Replaces lost resin from Tarmac, vastly superior to bitumen based tarmac paint
- 20 litre drum, average coverage 40 to 60 sq metres
- Easy to apply with roller
- Re-creates original colour of Tarmac
- Avoids need for expensive replacement of asphalt
- Long term protection, reduces future Tarmac repair
- Covers unsightly cement marks & oil stains
- Water based Tarmac Repair coating, environmentally friendly easy to apply product
- Top up coats of Tarmac sealer can be applied at any time
- Reduces Tarmac stone loss and increases the life span of Tarmac driveways
- Waterproofs, re-colours and protects Tarmac
- Resists oil, grease and dirt stains
- Resists fungicidal and algae growth
Preparation
Ensure the surface is thoroughly cleaned with a pressure washer or jet washer. Allow a minimum of 2 to 3 clear, dry days before sealing. Before coating, sweep area and remove any loose stones. Make sure product is thoroughly mixed with no sediment present.
Application
For best results apply 2 coats in temperatures above 12°C and below 22°C Only apply if no rain is forecast for at least 6 hours.
Tarmaseal can be applied via a medium pile roller or large paint brush. Make sure a minimum of 2 to 4 hours is left between coats.
Health & Safety
All work should be carried out with safety goggles, mask and gloves.
*Tarmaseal is primarily for rejuvenating the existing colour of tarmac and should not be used to change the existing colour.
Q: When I have finish painting & rolling the Tarmac restrer what do I clean the brushes & rollers with? Thanks
A: Thanks for the question. Warm soapy water or white spirit should help with this.
Q: After cleaning bricks on the front of my house using brick acid It has stained my tarmac drive will your tarmac restore cover these stains ?
A: The Tarmac Restorer BLACK is likely to cover and disguise the stained tarmac you have described. However, to make sure it would be best to carry out a small test patch with a sample first.
Q: Can I use this to change my red driveway to black? It is a tarmac drive.
A: Thanks for the question. This is not something we would recommend. There is a chance the original colour would start showing through. If you were to go ahead, you would need more treatment sooner compared to keeping it the same colour.
My tarmac drive measures approx 50 m2, so I ordered two 20 litre containers of Tarmaseal (as one 20 litre container is supposed to cover 40-60 m2 and two coats is recommended). Preparation consisted of giving the south-facing drive a thorough sweep, filling a small hole with the crack repair compound and treating a couple of oil stains with the oil stain remover. I didn't power hose the drive as I don't posses a power hose. The first coat took 7 hours to apply using the roller kit and a brush to the edges, and I used the whole of one container as the drive was quite worn (over 20 years old). The second coat took just 2.5 hours and used about half of the second container, so I gave the drive a third coat as I had enough Tarmaseal left over. The final result looks very impressive, almost like new, with a consistent finish.
Used this tarmac restorer four years ago and the result was so good I have ordered more to treat another part of my tarmac. Easy to use, spreads well and looks good when finished.
Good product easy to apply and excellent finish on old 'well worn' tarmac. Make sure to have plenty of containers, roller sleeves and brushes ready before starting the application.